The wishlist name can't be left blank
×

:

Not a valid Time
This is a required field.
DCD 1-1/4

DCD 1-1/4" Diameter Hexagon Clevis Pin Kit 1/EA

DCD 1-5/8

DCD 1-5/8" Diameter Hexagon Clevis Pin Kit 1/EA

DCD 1-3/8" Diameter Hexagon Clevis Pin Kit 1/EA

$32.83
Availability: Pending Availability



SKU
DCD 00025-HEX
Sold Per 1 Each DCD 1-3/8" Diameter Hexagon Clevis Pin Kit Product Information:

All clevis pins are manufactured from heat treated 416 stainless steel to provide superior strength and wear. Hardness is between 37-40 Rc.

The DCD Clevis Pin is a shouldered type of pin rather than a simple straight pin without any head. This design greatly improves the strength of the clevis by not allowing side loads to spread the clevis opening. The clevis and pin are precision machined so that both surfaces contact simultaneously and therefore lock in place when screwed tight. Tensile loads are carried by the pin shoulder and transferred to the swivel body, and therefore no tensile load is carried by the thread

The hardened clevis pin also resists wear much better than conventional clevis pins. During operation there is a constant rubbing between the surface of the clevis pin and the attached item. A hard surface decreases the wear on the pin as well as increasing the strength of the pin

Finally, the larger diameter of the shoulder will decrease wear on the attached item. If this happened to be a wire rope, for example, a conventional pin would cause that rope to bend in a very tight radius, affecting the life of each strand. The larger DCD pins increase that radius and also increase the life of the wire. Products 1-1/4" diameter and less are supplied with slotted clevis pins; those greater than 1-1/4" are supplied with hexagon socket clevis pins. This is based on consumer preference. Either slotted or hexagon pins are available for most sizes but must be requested at time of ordering if not standard

Because the DCD clevis pin is a precision machined product specifically designed to fit the clevis, field substitution with any other pins is not recommended. Doing so may cause serious danger to operators and equipment and will immediately void any warranty or liability for the product

All clevis pin kits contain 2 pins Hexagon Part No.: 00025-HEX Hex Key Size: 5/16" A: 1-3/8" B: 9/16" C: 1/2" D: 1-3/8" E: 5/8" F: 1/2" Recommended Torque (ft-lb): 16.7 ft-lb Corresponding Preload: 2,667 lbs. Weight: 0.12 lbs.

More Information
Alt ProductID 00025-HEX
Diameter 1-3/8"
Weight 0.120000
New Yes
Description Sold Per 1 Each DCD 1-3/8" Diameter Hexagon Clevis Pin Kit Product Information:

All clevis pins are manufactured from heat treated 416 stainless steel to provide superior strength and wear. Hardness is between 37-40 Rc.

The DCD Clevis Pin is a shouldered type of pin rather than a simple straight pin without any head. This design greatly improves the strength of the clevis by not allowing side loads to spread the clevis opening. The clevis and pin are precision machined so that both surfaces contact simultaneously and therefore lock in place when screwed tight. Tensile loads are carried by the pin shoulder and transferred to the swivel body, and therefore no tensile load is carried by the thread

The hardened clevis pin also resists wear much better than conventional clevis pins. During operation there is a constant rubbing between the surface of the clevis pin and the attached item. A hard surface decreases the wear on the pin as well as increasing the strength of the pin

Finally, the larger diameter of the shoulder will decrease wear on the attached item. If this happened to be a wire rope, for example, a conventional pin would cause that rope to bend in a very tight radius, affecting the life of each strand. The larger DCD pins increase that radius and also increase the life of the wire. Products 1-1/4" diameter and less are supplied with slotted clevis pins; those greater than 1-1/4" are supplied with hexagon socket clevis pins. This is based on consumer preference. Either slotted or hexagon pins are available for most sizes but must be requested at time of ordering if not standard

Because the DCD clevis pin is a precision machined product specifically designed to fit the clevis, field substitution with any other pins is not recommended. Doing so may cause serious danger to operators and equipment and will immediately void any warranty or liability for the product

All clevis pin kits contain 2 pins Hexagon Part No.: 00025-HEX Hex Key Size: 5/16" A: 1-3/8" B: 9/16" C: 1/2" D: 1-3/8" E: 5/8" F: 1/2" Recommended Torque (ft-lb): 16.7 ft-lb Corresponding Preload: 2,667 lbs. Weight: 0.12 lbs.