The wishlist name can't be left blank

DCD 5'-8' Short Extension Manhole Brace 1/EA

In stock
SKU
DCD 32700-010
$1,035.50
Sold Per 1 Each DCD 5'-8' Short Extension Manhole Brace Product Information: The DCD Manhole Brace may look like other products on the market, but look again. There are several features which make it stand out from other similar products

Pivoting Head - In many applications the top of the brace cannot jam against a round manhole, instead it may be jammed against a square cutout in the roof of the manhole vault. The DCD Manhole Brace has a pivotable upper head which allows the brace and sheave to be accurately aligned with the duct bank without the need for temporary shoring/bracing

Custom Extruded Channels - The aluminum channels have been custom extruded to an engineered design. Their shape provides the maximum strength-to-weight ratio while also providing a smooth sliding action. The channels have approximately twice the strength as the standard aluminum channels used in similar products, allowing a full 10,000 lb line load to be applied at either entry or exit end of the pull. This load allows in excess of a 2:1 safety factor

Fixed Angle - The brace operates at a fixed angle of 10 There is an acme screwjack assembly to adjust the height of the brace. This same screw can be used to relieve the pressure on the brace when it is being removed

Lifting Bar - The lifting bar provided allows the user to easily raise the upper extension into its correct position. This bar can be swung out of the way and stored when not in use

Locking Pins - The brace uses separate locking pins for each set of channels. Using two locking pins ensures that they do not interfere with the desired placement of the sheave or quadrant

Fixed Width - This fixed width brace is designed to accept quadrants or sheaves up to 8" wide. Since correct alignment to the duct entrance is now possible with the rotating head, even use of only a 4" wide sheave is no problem inside the 8" available width the sheave will simply float between the side rails always picking up the most favorable alignment

Construction Although the side channels are extruded aluminum, the upper and lower assemblies are made out of steel. While increasing the overall weight by a few pounds, the added strength of steel is necessary in order to match the strength of the extruded side channels. The end result is a brace that can operate equally at either end of the pull and one that will match the safe working loads of all other DCD manhole products at 10,000 lbs. The base section is used in all assemblies and comes complete with 2 locking pins and 1 sheave pin. The short, medium or long extension should be ordered to suit the height range requirement

Locking pins and sheave pins c/w securing pins may be ordered separately Part No.: 32700-010 Height Range: 5'-8' Weight: 54.50 lbs.

More Information
Alt ProductID 32700-010
Weight 54.500000
Size 5 - 8 FT
New No
Description Sold Per 1 Each DCD 5'-8' Short Extension Manhole Brace Product Information: The DCD Manhole Brace may look like other products on the market, but look again. There are several features which make it stand out from other similar products

Pivoting Head - In many applications the top of the brace cannot jam against a round manhole, instead it may be jammed against a square cutout in the roof of the manhole vault. The DCD Manhole Brace has a pivotable upper head which allows the brace and sheave to be accurately aligned with the duct bank without the need for temporary shoring/bracing

Custom Extruded Channels - The aluminum channels have been custom extruded to an engineered design. Their shape provides the maximum strength-to-weight ratio while also providing a smooth sliding action. The channels have approximately twice the strength as the standard aluminum channels used in similar products, allowing a full 10,000 lb line load to be applied at either entry or exit end of the pull. This load allows in excess of a 2:1 safety factor

Fixed Angle - The brace operates at a fixed angle of 10 There is an acme screwjack assembly to adjust the height of the brace. This same screw can be used to relieve the pressure on the brace when it is being removed

Lifting Bar - The lifting bar provided allows the user to easily raise the upper extension into its correct position. This bar can be swung out of the way and stored when not in use

Locking Pins - The brace uses separate locking pins for each set of channels. Using two locking pins ensures that they do not interfere with the desired placement of the sheave or quadrant

Fixed Width - This fixed width brace is designed to accept quadrants or sheaves up to 8" wide. Since correct alignment to the duct entrance is now possible with the rotating head, even use of only a 4" wide sheave is no problem inside the 8" available width the sheave will simply float between the side rails always picking up the most favorable alignment

Construction Although the side channels are extruded aluminum, the upper and lower assemblies are made out of steel. While increasing the overall weight by a few pounds, the added strength of steel is necessary in order to match the strength of the extruded side channels. The end result is a brace that can operate equally at either end of the pull and one that will match the safe working loads of all other DCD manhole products at 10,000 lbs. The base section is used in all assemblies and comes complete with 2 locking pins and 1 sheave pin. The short, medium or long extension should be ordered to suit the height range requirement

Locking pins and sheave pins c/w securing pins may be ordered separately Part No.: 32700-010 Height Range: 5'-8' Weight: 54.50 lbs.